> [!NOTE]+ Meta > Author:: Songül ARAL > Reference:: https://garlandmag.com/article/tepelikler-anatolian-headdress/ > Date:: 2023-03-27 > Tags:: #Turkey #jewellery #manuscript > WeftLinks:: [[Craft technique documentation]] ## Text ### Process 1: Designing. Process steps: Browse various jewelry-related resources. Choose appropriate motifs and forms. Prepare draft drawings. Draw the final form you have determined. Prepare drafts. Identify the drafts that are suitable for the application. Determine the materials suitable for the design. Determine your colors. Identify the techniques. Determine the materials to be used. Give the design its final shape. ### Process 2: Preparing the tools suitable for the design. Process steps: Determine the counter suitable for the design (wood or plastic) Get a hammer, awl, utility knife, small pliers, round-nose pliers, chisel pliers, and a paint brush. ### Process 3: Preparing a bench suitable for the design. Process steps. 26x58 cm. Get a size board. On the board, draw the size from neck to chest, suitable for size 38, with a pencil. On the determined measure, the upper ends are 0.5 cm. spaced out. Do the same for the lower end. Nail glass nails to the marks on the lower and upper ends. ### Process 4: Preparing the materials suitable for the design. Process steps: Take medium thickness and yellow colored jewelry wire. (2 reels) Take a number nine waxed and yellow thread bobbin. Get a cotton boll. (20 pieces) Get a golden yellow fabric dye. Take the nail with the jewelry assembly cap. (2 small packs) Get a jewelry union ring. (2 small packs) Take yellow, green and brown cotton embroidery thread. ### Process 5: Preparing the workbench according to the design. Process steps: Buy a board suitable for the upper body size. On the board, draw the size from neck to chest, suitable for size 38, with a pencil. Drive a glass nail on the specified size so that the lower and upper ends are parallel. 0.5 cm of nails. Make sure it's intermittent. ### Process 6: Preparing the warp with wire on the loom. Process steps. Secure it by wrapping the wire from the top nail. Extend it to the lower nail and go around one turn. Wrap the wire around the nail next to the nail you started by stretching it one turn. Repeat the second step and apply to all nails. ### Process 7: Starting to weave on the warp Pull a row of chains. For Rococo; Pull the two warp wires from the inside to the bottom with the help of crochet, wrapping the rope 5 times on top. Knit snowballs on the warp pair next to it. For the snowball; you will return as a view from under the lines. We have been gifted your training 5 times, behind the strength knitting. Complete your snowball knitting so that it passes under the warps above the horizontal transition. Complete the knitting sequence by repeating from the 2nd step of the 5th process. Draw two rows of chains on the top of the row of snowballs and rococo. Continue to knit with 1 row of snowballs and rococo, and 2 rows of chains. Complete 4 rows of snowball and rococo, 2 rows of chain knitting in between. After this row, start knitting only the rococo and chain, up to the neck measurement. Continue knitting rococo and 2 rows of chains in each warp pair until you reach the neck studs. Complete your weaving with a chain, with 2 rows of chain knit on top of 4 rows of rococo knit. #### SUB-PROCESSING STEPS Process steps. Pull a string of fences/chains. Sub-Process steps 7: Making the fence/chain. Take your waxed thread in your hand. Knot the wire at the top left. Pass one end of the yarn from the bottom to the top of the other end. Make a loop from the top rope. Pull the bottom thread through the loop. Create the chain. Repeat these steps. Build the fence. ### Process 8: Making Rococo. For Rococo; Pull the two warp wires from the inside to the bottom with the help of crochet, wrapping the rope 5 times on top. Process steps. Fix your thread on the two warp wires. Wrap your rope around it five times. Take the hook in your hand. Pass the end of your yarn through the yarns you wrapped with the help of crochet. Subtract from the lower end. Come out to the front as a diagonal from the back of the warp wire next to it. Knit snowballs on the adjacent warp pair. ### Process 9: Making Snowballs. For the snowball; pass under the yarn coming horizontally from under the warps and turn it circularly. Process steps. Continue with the rope you made rococo. Cross over the warp wire on the side. Go to the wire. Get out from the bottom. Repeat the last two steps. Pass over the remaining threads on the warp wire and under the warp wires. Repeat the last action five times. ### Process 10: Making the Back Snowball. Process steps. Repeat the steps you did in Process 9 in the opposite direction. Pass the top rope from the bottom and the bottom rope from the top. Repeat the last action five times. ### Process 11: Process repeat. Process steps. Repeat the 8.9.10. process and process steps until the sequence is completed. Continue to knit with 1 row of snowballs and rococo, and 2 rows of chains. Complete 4 rows of snowball and rococo, 2 rows of chain knitting in between. After this row, start knitting only the rococo and chain, up to the neck measurement. Continue knitting rococo and 2 rows of chains in each warp pair until you reach the neck studs. Complete your weaving with a chain, with 2 rows of chain knit on top of 4 rows of rococo knit. ### Step 12: Removing the weave from the loom. Process steps: Press on the braids with one hand to prevent them from slipping. Pull out the nails with the help of pliers. Bend the ends of the wires remaining at the neck with the help of flat pliers.   Attach the yellow rings one by one to the ends of the wires remaining on the chest with the help of pliers so that the warp wires of the weave do not slip off. Prepare a flat knotted macrame knit hanger in neck size from 12 waxed threads. This hanger; fix it to two double warp wires from the upper edge of the weave and knit as 4 wires. Gather the end of the braid in the form of a round buttonhole loop. Make ball beads with waxed thread and pass it through the buttonhole you made in the previous process. ### Process 13: Preparing the silk cocoons. Process steps: Cut the cocoons crosswise with the help of a utility knife. Clean them with the help of a brush. Paint inside and outside with fabric paint, let dry. Make a hole at the top with the help of a quilt needle. ### Process 14: Making small knitted flowers inside the cocoons. Process steps: ### Make 15 chains with the yellow thread. Return your crochet hook and count 4 chains and work into the 5th chain. Take the thread on the crochet hook and pull it from the chain, Gather the two ropes, Pull 6 chains, sink into the previous hole and collect the rope. Repeat the previous operation. Chain 15 and repeat the steps. Knit in other colors from the flowered chain knitting formed. ### Process 15: Placing knitting flowers inside the cocoons. Process steps: Bring together the yellow, green and brown flowers you made in step 14 and tie them in bunches. Fix your bouquet of flowers to the ring of the small jewelry nail with the help of crochet and thread.   Pass the jewelry nail through the cocoon hole. Make a ring on the tip of the nail with the help of pliers. On this ring, with your waxed knitting yarn, 5-6 cm from the length of your knitting. pull a long chain. Attach the yellow ring to the chain end. Place the flowers in 9 bolls by repeating the process. Attach the flower bunches to the cocoons that will be the other hanging ends, do not chain after the yellow rings are put on.(24 pieces) ### Process 16: Adding the cocoons to the knitted jewelry. Process steps: Fix the cocoons you prepared in Process 13 to the yellow rings on the lower ends of your knitting jewelry with the help of pliers. Bring together the 9 chained cocoons you have prepared and combine them into a single ring. Pin these cocoon dangles together behind the buttonhole and button closure of your knitting. ### Process 17: Making earrings. Process steps: One cocoon you prepared in Transaction 13; Attach it to the ring of the earring wire with the help of pliers. ### Process 18: Showcasing the jewelry design. Process steps: Display the jewelry by wearing it straight or obliquely over the shoulder on a size 38 mannequin. Weaving and knitting techniques; the loom was prepared using the existing material, the wooden cabinet shelf. The warp is prepared with the help of glass nail and metal wire. The application of weaving and knitting techniques applied on the warps enabled the production of functional jewelry. It is suitable for application for jewelry design works by using weaving and knitting techniques with the created loom. 1- List of Shapes. Jewelry design stages [[Attachments/aba5853ad15f31a4f527f8ab26aed822_MD5.jpeg|Open: Pasted image 20231109044152.png]] ![[Attachments/aba5853ad15f31a4f527f8ab26aed822_MD5.jpeg]] [[Attachments/8aff79a950a3377c6ed388baa2265698_MD5.jpeg|Open: Pasted image 20231109044228.png]] ![[Attachments/8aff79a950a3377c6ed388baa2265698_MD5.jpeg]] [[Attachments/bf27186d248c5448f6d7c9b8c75cf395_MD5.jpeg|Open: Pasted image 20231109044249.png]] ![[Attachments/bf27186d248c5448f6d7c9b8c75cf395_MD5.jpeg]]